Newsletter October 2019
Featured Product: SM-1 Large Capacity, Low Frequency Vibration
- Vertical natural frequency
of 1/2 Hz or less can be achieved over the entire load range.
- Horizontal natural
frequency is load dependent. 1/2 Hz or less can be achieved at or near the
- See typical
Performance for the SM-1.
SM-1 is low frequency vibration isolator for weight
loads from 500 to 4200 lbs. and 1/2 Hz performance vertical and horizontal.
The SM-1 negative-stiffness isolator is the basic building block of the
FP-1 Floor Platform and other heavy multiple
isolator systems. They require no air or electricity.
This isolator has
the same basic features of our all passive, negative-stiffness,
manually-adjustable bench top isolators. It offers our very-low frequency
isolation performance for payloads of many thousands of pounds.
SM-1 isolator can be used alone or with any number
of additional units to achieve higher capacity systems. They can be arranged in
many geometrical configurations to suit your application.
SM-1 isolators can also be placed on pedestals to
increase the height of the isolation system.
Pricing & Specifications
Work>>Negative-Stiffness Vibration Isolators
vibration isolators employ a revolutionary concept in
low-frequency vibration isolation. Vertical-motion isolation is provided by a
stiff spring that supports a weight load, combined with a negative-stiffness
mechanism (NSM). The net vertical stiffness is made very low without affecting
the static load-supporting capability of the spring. Beam-columns connected in
series with the vertical-motion isolator provide horizontal-motion isolation.
The horizontal stiffness of the beam-columns is reduced by the "beam-column"
effect. (A beam-column behaves as a spring combined with an NSM.) The result is
passive isolator capable of very low vertical and
horizontal natural frequencies and very high internal structural
isolators typically use three isolators stacked in series:
tilt-motion isolator on top of a horizontal-motion isolator on top of a
vertical-motion isolator. A vertical-motion isolator is shown in
1. It uses a conventional spring connected to an NSM consisting of two
flexures connected at their inner ends to the spring and supported at their
outer ends, and loaded in compression by forces P. The spring is compressed by
weight W to the operating position of the isolator, as shown in Figure 1. The
stiffness of the isolator is K=KS-KN where KS is the spring stiffness and KN is
the magnitude of a negative stiffness which is a function of the design of the
flexures and the load P. The isolator stiffness can be made to approach zero
while the spring supports the weight W.
horizontal-motion isolation system consisting of two beam-column isolators is
shown in Figure 2. Each isolator behaves like two fixed-free beam
columns loaded axially by a weight load W. Without the weight load the
beam-columns have horizontal stiffness KS. With the weight load the lateral
bending stiffness is reduced by the "beam-column" effect. This behavior is
equivalent to a horizontal spring combined with an NSM so that the horizontal
stiffness is K=KS-KN, and KN is the magnitude of the beam-column effect.
Horizontal stiffness can be made to approach zero by loading the beam-columns
to approach their critical buckling load.
Full article +
Custom Vibration Isolation
Minus K engineers can design a variety of custom vibration
isolation systems. Frequently these are modifications of other designs such as
changing the load capacity of an
SM-1 isolator, or the capacity, size and
isolator locations on a
Custom table top with four resessed Minus K
CM-1s and pedestals
Some other custom modifications and capabilities
vertical, horizontal or tilt stiffness in an isolator
vertical, horizontal or tilt damping in an isolator
- Heavy load
(Six 10,000 lb
isolators for NASA's James Webb
Space Telescope Ground
- Compact systems
(e.g., a seven-inch cubic 1/2 Hz isolator for a 700 lb payload;
diameter by 4-inches tall 1/2 Hz vibration isolation platform for a 3 lb
auto-adjust feature to automatically adjust for change in payload
feature implemented manually with a switch or automatically
from a stage motion control system, for example.
Audio Reproduction & Turntable
Platforms, Tables, & Integrated
Since the early 2000s, Minus K Technology, the developer of
Negative-Stiffness vibration isolation, has released several vibration
isolation platforms for the high-end audio market. These products have been
accepted with high acclaim by audiophiles and audio system manufacturers
The industry's highest performing vibration isolation system
is available in a cost-effective, low-height platform. The
BM-8 Series vibration
isolation platform offers true ½-Hz isolation performance vertical and
1.5 Hz horizontal and is easy to use. No air or electric power is required,
there is no maintenance and nothing to wear out. It is 18Wx20Dx4.6H and is
available with nominal load capacities from 25 to 250 lbs. It is ideal for
turntables, CD transports and other audio components.
The Helix One®
and Helix Two® turntables from Dohmann Audio, for example, come fully
integrated with Negative-Stiffness vibration isolation.
Doehmann Helix 1 (BM-8 fully integrated)
Doehmann Helix 2 (BM-10 fully integrated)
of Negative-Stiffness to deal with vibration and resonance is unsurpassed, and
allows the music to be enjoyed with an outstanding level of
Analog audiophile aficionados talk about blackberry notes,
where the base is too prominent and muddy, explained Dohmann. This is often
caused by a reinjection of vibration into the playback mechanism, adding to the
amplitude of the needle movement and creating more signal that what is
physically in the groove. But Negative-Stiffness vibration isolation cleans
this up, so that the base is more natural. The timbre of the instrument used to
produce the base, whether a string, piano or drum, sounds more like the real
thing. It enables a sense of peace and calm to the playback."
Mark Döhmann, Founder Döhmann Audio
The latest generation of Negative-Stiffness vibration isolation
technology, embodied within the new ultra-thin, low-hieght Minus K
CT-1, truly represents
a significant advance in sound quality in a very compact package for high-end
SAT (Swedish Analog Technologies) XD1 Record Player
with Minus K
CT-1 [integrated into the
BM-1 Series platform
offers Minus K's signature 0.5 Hz performance, both vertical and horizontal,
and is available for larger and much heavier audio components.
| I have now tried the
CT-1 with the SAT top
platform the results are spectacular! I took a look at the mechanism inside of
the CT-1 and I have to say I am very impressed with the ingenious work you have
done. It provides most of its big brothers performance in an extremely compact
package that looks very slick. The arrangement and the finish of the mechanism
is an engineers dream and it should be proudly displayed. The equipment
supported by the CT-1 is well isolated from vibrations from 0.7 to 100 Hz, with
much deeper, clearer base and more information in the lower frequencies. The
CT-1 makes a huge difference in sound quality."
- Marc Gomez,
President / Swedish Analog Technologies SAT
BM-10 Series offers
smaller horzontal dementions at 12.2 W x 12.2 D x 4.6 H (310mm W x 310mm D x
More images, plus reviews and
Tables, Platforms, Benchtops & Custom Systems for
SEM, AFM, TEM, SPM, STM, STEM, NSOM-SNOM
Obersver Z1 AFM
on a Minus K
on a Minus K
Nion STEM on a
on a Minus K
of our clients' microscopes have nano and micro vibration isolation
requirements that are unparalleled in the metrology world (for
research and at
NASA as examples). Minus K's negative
stiffness and "passive" verses "active" technology, enables microscopes to
achieve their highest level of performance. Our
custom systems provide the performance of an
ideal bungee system and the convenience of a bench top system without any of
the problems associated with many of them, including air tables.
the ubiquitous bungee suspension systems, to large beds of sand on inner tubes,
there have been many attempts at achieving the ultimate isolation. Air tables
have been used with some success. However, our negative-stiffness isolators
provide superior isolation control and performance while offering better ease
of use and no facility requirements. We even have the flexibility of custom
tailoring resonant frequencies vertically, horizontally and in tilt to your
Small "active" systems (as opposed to our "passive" systems) are
sometimes used. However, those have several drawbacks:
isolators give you the best possible
performance in all axes, from high to low frequency isolation. They provide the
performance of an ideal bungee system and the convenience of a bench top system
without any of the problems associated with any of them, including air tables.
We enable our users to achieve the highest level of noise performance possible.
- They are
expensive and fragile.
- They are
subject to the noise floor of every component in the entire feedback loop plus
AC line noise.
have a limited dynamic range, typically only a few thousandths of an inch. If
this is exceeded (very easy to do) the isolator goes into positive feedback and
you have a very expensive noise generator underneath your SPM.
have to be sitting on an infinitely rigid structure to work at their
theoretical best. Obviously, infinitely rigid structures are not easy to find
in most labs. The result is that the isolator is not always doing what you
think it's doing.